2L inc., Massachusetts, USA
Call Us: 1(978)567-8867 | Email | Contact | Sign In |

2L inc. www.2Linc.com

Fixturing and Vacuum Workholding Accessories

Workholding Accessories for the 2L Modular and Large Vacuum Chucks, Pallet System, Vacuum Pumps & Many  Other Applications

These Fixturing and Vacuum Workholding Accessories are for use with a wide range of applications: 2L Modular and Large Size Vacuum Chucks, Portable Electric Vacuum Pump, and many other workholding products and applications.

Page down for all items:
Adjustable Workstops and Edge Clamps – Vacuum Filter, O-Rings, and other Replacement Items for the Portable Oil Free Electric Vacuum Pump – Adjustable Vacuum Pressure Switch – Replaceable Top Plates for Vacuum Chucks – Quick Disconnects – Vacuum Gauge – Gasket Cords – Vacuum Manifolds – Vacuum Port Assemblies – Vacuum Hose Kit and more.

Adjustable Workstops & Edge Clamps

  • Use a Hex Workstop and an Edge Clamp to securely hold various size parts.
  • Use with 2L Modular Vacuum Chucks, Pallet System, Large Vacuum Chucks and many other fixturing systems.
  • Tighten the standard flathead screw to move the Edge Clamp toward the workpiece.
  • Numbered locations allow for repeatable setup.
  • Low profile for maximum clearance.
  • Black Oxide Steel Construction.
  • A 1/4″ – 20 screw is included with each Workstop and Edge Clamp.
Adjustable Hex Workstop

Adjustable Hex Workstop

  • Varying distances from each edge to the central hole (0.050″) each stop) allows adjusting workpiece location.
  • Part No. 10247.
  • $23.75 each.
Adjustable Corner Edge Clamp

Edge Clamp

  • Hardened Steel.
  • Provides 1.25″ clamping travel range when used with an Adjustable Edge Clamp.
  • Part No. 10248.
  • $27.50 each.
Adjustable Corner Edge Clamp

Corner Edge Clamp

  • Hardened Steel.
  • Cutout on ends allows holding corners of workpieces or circular workpieces.
  • Provides 1.25″ clamping travel range when used with an Adjustable Hex Workstop.
  • Part No. 10272.
  • $35.00 each.
Adjustable Thin Corner Edge Clamp

Thin Corner Edge Clamp

  • Hardened Steel.
  • Thin (0.06″) cut out ends allows holding very think workpieces or circular workpieces.
  • Provides 1.25″ clamping travel range when used with an Adjustable Hex Workstop.
  • Part No. 10273.
  • $40.00 each.

Portable Electric Vacuum Pump

Adjustable Vacuum Pressure Switch

10.1 Amp Adjustable Vacuum Pressure Switch

End Cap Assembly for Electric Vacuum Pump

End Cap Assembly

  • For use with the 2L Portable Oil-Free Electric Vacuum Pump.
  • Includes:
    • 1 – End Cap Filter.
    • 1 – End Cap.
  • Part No. 10748.
  • $22.75 each.
End Cap Assembly O-Ring

O-Rings for End Cap

  • For use with the 2L Portable Oil-Free Electric Vacuum Pump.
  • Part No. 10962.
  • $9.50, Pkg. of 2.
Electric Vacuum Pump Filter Housing

Filter Housing

  • Vacuum Filter Housing for Portable Electric Vacuum Pump.
  • Includes Cap and Clear Housing.
  • Part No. 10690.
  • $97.50 each.
Electric Vacuum Pump Filter Replacement Mesh Filter

Mesh Filter

  • For use in the Vacuum Filter Housing.
  • Part No. 10719.
  • $123.00 each.
Vacuum Filter O-Ring

O-Ring for Filter Housing for Electric Vacuum Pump

  • Air Sealing O-Ring for Vacuum Filter Housing.
  • Part No. 10733.
  • $12.50 each.
Filter Wrench for Electric Vacuum Pump Filter Housing

Filter Wrench

  • For use with the Vacuum Pump Filter Housing of the Portable Electric Vacuum Pump.
  • Part No. 10689.
  • $17.50 each.
Vacuum Hose Kit for Vacuum Workholding

Vacuum Hose Kit

  • Allows vacuum source to be located away from your machine.
  • Includes:
    • 10 feet hose length, 5/8″ ID-7/8″OD.
    • 2 – 5/8″ hose barbs.
    • 2 – 3/8″ F NPT-1/4″ M NPT hex adaptors.
    • Hose clamp.
  • Part No. 10262.
  • $96.45 each.
Vacuum Pump Repair Kit

Electric Vacuum Pump Motor Repair Kit

  • For use with the 2L Portable Oil-Free Electric Vacuum Pump.
  • Kit includes:
    • 4 – Graphite Vanes.
    • 1 – Gasket.
    • 2 – End Cap Filters.
    • 2 – O-Rings for End Cap Filters.
  • Part No. 10687.
  • $195.95 each.

Modular Vacuum Chucks & Modular Pallet System

Modular Vacuum Chuck Alignment Pins

Alignment Pins

  • Use with the Modular Vacuum Chucks & Modular Pallet System.
  • Heavy duty steel pins align and guide two or more Pallets together.
  • Part No. 10356.
  • $7.50, Pkg. of 2.
1/8" Diameter Gasket Cord for Vacuum Chucks and Top Plates

Gasket Cord - 1/8" Dia.

  • Fits into slots of Modular Vacuum Chucks and all Replaceable Top Plates.
  • Gasket Cord provides vacuum seal.
  • 1/8″ diameter x 100 ft length.
  • Part No. 10250A.
  • $81.25 each.
8" x 12" Gasket Sheet for Modular Vacuum Chucks

Gasket Sheet - 8" x 12"

  • Use with Modular Vacuum Chucks to provide vacuum seal.
  • Allows machining through parts.
  • To use: cut out the area beneath part and place Gasket Sheet and part on Vacuum Chuck.
  • Part No. 10253.
  • $20.50 each.
Multiple Pallet Connector for Modular Vacuum Chucks

Muliple Pallet Connectors

  • For use with the 8″ x 12″ Modular Vacuum Chucks.
  • Connect two or more Vacuum Chucks together to increase the size of workspace.
  • Includes one (1) Connector & four 5/16″ – 18 screws.
  • Part No. 10258.
  • $40.00 each.
Vacuum Hose Quick Disconnects

Quick Disconnects

  • Straight through couplings allow quick hose disconnect. No internal valves in couplings.
  • Each contains 1 plug and 1 socket.
  • Two sizes – seel  below.

1/4″ M-1/4″M.

  • Part No. 10373.
  • $38.50 each.

3/8″ M – 3/8″M.

  • Part No. 10374.
  • $44.10 each.
Replaceable Top Plates for Vacuum Chucks

Replaceable Top Plates

Vacuum Connector for Modular Vacuum Chucks

Vacuum Connector

  • Connects two or more Modular Vacuum Chucks and increase the size of your workholding area while using only one Vacuum Pump.
  • Part No. 10271.
  • $30.00 each.
Vacuum Pressure Gauge

Vacuum Gauge

  • 2″ diameter dial with steel case and plastic lens.
  • 1/4″ NPT Male brass fitting.
  • Part No. 10034.
  • $21.58 each.
Vacuum Hose Kit

Vacuum Hose Kit

  • Allows vacuum source to be located away from your machine.
  • Includes:
    • 10 feet hose length, 5/8″ ID-7/8″OD.
    • 2 – 5/8″ hose barbs.
    • 2 – 3/8″ F NPT-1/4″ M NPT hex adaptors.
    • Hose clamp.
  • Part No. 10262.
  • $96.45 each.
Vacuum Manifold - Vacuum Gauge and Shut Off Valves for Workholding

Vacuum Manifold

  • Use to connect the Vacuum Chuck to a vacuum source.
  • Includes:
    • Vacuum Gauge.
    • Brass Tee Fitting.
    • 2 – 1/4” M NPT – 1/4” M NPT Fitting.
    • 2 shut-off valves.
  • Part No. 10270.
  • $91.15 each.
Vacuum Plug for Modular Vacuum Chucks

Vacuum Plug

  • Plugs the side vacuum connector holes on the Modular Vacuum Chucks.
  • Part No. 10254.
  • $16.25, Pkg. of 8.
Vacuum Plug Screw for Modular Vacuum Chucks

Vacuum Plug Screw

  • Screws into any of the tapped holes of the Modular Vacuum Chucks to seal and block escape of vacuum air to increase hold.
  • Part No. 10246.
  • $8.50, Pkg. of 10.
Vise Stop Pin Locates Vacuum Chuck in Vise

Vise Stop-Pin

  • Steel Pin locates the Modular Vacuum Chuck or Pallet Fixturing System Pallet in the milling vise.
  • Screw into any of the twelve Stop-Pin holes to consistently locate the pallet in your vise.
  • Part No. 10252.
  • $30.00 each.
Vise Block to Hold Vacuum Chuck in Vise

Vise-Block

  • Attach to the bottom of the Modular Vacuum Chuck or Pallet Fixturing System Pallet to allow for use in a 5″ or larger milling vise.
  • Steel Black oxide construction.
  • Includes:
    • Vise-Block – 5″ W x 7″ OL x .5″ H.
    • Six (6) 1/4″ – 20 screws.
  • Part No. 10260.
  • $168.75 each.
Side & End Stops for Modular Vacuum Chucks

Workstops - Side & End

  • Attach to the sides and ends of the Modular Vacuum Chuck to locate the workpiece.
  • The height of the workstops can be adjusted to allow for clearance of your tool.
  • Choose from below Work Stops.

Side Workstop – 1″ H x 12″ OL.

  • Part No. 10255.
  • $45.00 each.

End Workstop – 1″ H x 8″ OL.

  • Part No. 10256.
  • $45.00 each.

Large Vacuum Chucks

1/8" x 5/16" Gasket Cord for Vacuum Chuck Workholding

Gasket Cord - 1/8" x 5/16"

  • Fits into slots of Large Vacuum Chucks.
  • For use with the 13″ x 25″, 18″ x 36 and 24″ x 48″ Vacuum Chucks.
  • Recommended for holding smaller workpieces.
  • 1/8″ x 5/16″ x 50 ft length.
  • Part No. 10543.
  • $64.75 each.
3/16" x 5/16" Gasket Cord for Vacuum Chuck Workholding

Gasket Cord - 3/16" x 5/16"

  • Fits into slots of Large Vacuum Chucks.
  • For use with the 13″ x 25″, 18″ x 36 and 24″ x 48″ Vacuum Chucks.
  • Recommended for holding larger workpieces.
  • 3/16″ x 5/16″ x 50 ft length.
  • Part No. 10544.
  • $64.75 each.
Replaceable Top Plates Protect Surface of Vacuum Chuck

Replaceable Top Plates

3 Port Vacuum Pump Assembly

3 Port Assembly

  • For use with the 13″ x 25″ Large Vacuum Chucks.
  • Part No. 10816.
  • Price $285.40.
4 Port Vacuum Pump Assembly

4 Port Assembly

  • For use with the 18″ x 36″ Large Vacuum Chucks.
  • Part No. 10542.
  • Price $335.75.
4 Port Vacuum Pump Assembly

4 Port Assembly

  • For use with the 24″ x 48″ Large Vacuum Chucks.
  • Part No. 10550.
  • Price $335.75.

You may also like…