Vacuum Chuck Accessories for Modular Vacuum Chucks

8" x 12" Modular Vacuum Chuck Accessories & Vacuum Workholding Accessories

The accessories shown below are for use with the 8" x 12" Modular Vacuum Chucks and Chuck Systems.

These vacuum accessories are in stock.
Order below or contact us.

Accessories for 8" x 12" Modular Vacuum Chucks
Alignment Pin	Heavy duty steel pin aligns and guides two or more Modular Vacuum Chuck Pallets together for even surface transition. 2 Alignment Pins are needed to connect 2 Pallets together. Alignment Pin Catalog No.: 10356 Quantity: $6.00 Pkg. of two
8" x 12" Aluminum Vacuum Chuck Top Plate	Precision ground, replaceable aluminum plate for covering the surface of the Modular Vacuum Chuck. Allows drilling through or machining around the outside of workpieces without damaging the vacuum chuck. Includes 5 machine-able brass screws for securing in place. Numbered hole locations allow for quick set ups and consistent workpiece placement. 8" width x 12" length x 3/8" thickness. *Customized Top Plates are also available with minimal delivery times.* 8" x 12" Top Plate Catalog No.: 10439 Quantity: $198.00 each
Double Sided Workholding Tape	Firmly holds workpieces in position. One side has a strong permanent adhesive. The other is coated with a removable adhesive. The removable adhesive allows removal of the workpiece without damaging it or leaving residue. It also allows for removal and repositioning of the workpiece many times. 1 roll - 1” width x 36 yards length. Double Sided Tape Catalog No.: 10276 Quantity: $21.00 roll
Gasket Cord	Fits into the slots of the Modular Vacuum Chuck, All Replaceable Aluminum Top Plates. Used to provide a vacuum seal. 1/8" diameter - 100 ft. roll 1/8" Gasket Cord Catalog No.: 10250 Quantity: $49.96 roll
Gasket Sheet	Provides vacuum seal and allows machining through parts without damaging the Modular Vacuum Chuck. To use, cut out the area beneath your part with a razor blade and place the Gasket Sheet and the workpiece on the Vacuum Chuck. 8" width x 12" length x 1/8" height. Gasket Sheet Catalog No.: 10253 Quantity: $16.25 each
Multiple Pallet Connector for Modular Vacuum Chucks	Lock two or more 8" x 12" Modular Vacuum Chucks together to increase the size of the workspace area. Pallet Connectors can also be used as a clamping area to hold the pallet down to the machine table. Includes four 5/16"-18 screws to connect to your Pallet. A minimum of four Pallet Connectors are needed to connect 2 Vacuum Chuck Pallets. When connecting 3 or more Pallets the quantity needed will depend on your Pallet layout configuration. Multiple Pallet Connectors Catalog No.: 10258 Quantity: $32.00 each
Quick Disconnect Couplings	Straight through couplings allow quick hose disconnect. No internal valves in couplings. Contains 1 plug and 1 socket. Available in two sizes. Quick Disconnect Couplings 1/4" M - 1/4" M: Catalog No.: 10373 - Use when connecting the quick disconnect between the Vacuum Chuck and Vacuum Hose. 3/8" M - 3/8" M: Catalog No.: 10374 - Use when connecting the quick disconnect between the Vacuum Hose and Electric Vacuum Pump. 1/4" Quick Disconnect Catalog No.: 10373 Quantity: $21.50 each 3/8" Quick Disconnect Catalog No.: 10374 Quantity: $26.50 each
Vacuum Connector	Used to connect two Modular Vacuum Chucks together while using only one Vacuum Pump. Vacuum Connector Catalog No.: 10271 Quantity: $24.00 each
Vacuum Gauge	Allows quick reading of vacuum function. 2" diameter dial with steel case and plastic lens. 1/4" NPT Male brass fitting. Use with Vacuum Chucks, Electric Vacuum Pump, Venturi Vacuums and many other Vacuum applications. Vacuum Gauge Catalog No.: 10034 Quantity: $16.60 each
Vacuum Hose Kit	Hose allows your vacuum to be located away from your machine. Has 1/4” NPT and 3/8” NPT connectors. Includes: 10 feet length Hose, 2 - 5/8" hose barbs, 2 - 3/8" F NPT - 1/4" M NPT Hex Adaptors, Hose Clamp. Use with Vacuum Chucks, Electric Vacuum Pump, Venturi Vacuums and many other Vacuum applications. Vacuum Hose Kit Catalog No.: 10262 Quantity: $69.95 each
Vacuum Manifold	Use to connect the Vacuum Chucks to a Vacuum Pump. 1/4" NPT threads. Manifold includes: Vacuum Gauge, Brass Tee Fitting, 2-1/4" M NPT - 1/4" M NPT Fittings, 2 shut-off valves. Use with Vacuum Chucks, Electric Vacuum Pump, Venturi Vacuums and many other Vacuum applications. Vacuum Manifold Catalog No.: 10270 Quantity: $67.32 each
Vacuum Plug	Used to plug the side Vacuum Connector Hole if only one Modular Vacuum Chuck is being utilized. Vacuum Plug Catalog No.: 10254 Quantity: $13.00 pkg. of 8
Vacuum Plug Screw	Seals vacuum holes on the Modular Vacuum Chucks to block escape of vacuum air to increase hold. Screws into any of the tapped holes of the Modular Vacuum Chucks. Vacuum Plug Screw Catalog No.: 10246 Quantity: $4.00 pkg. of 10
Workstops: Side Workstops & End Workstops for the 8" x 12" Modular Vacuum Chucks	Attach to the sides and ends of the Modular Vacuum Chuck to locate the workpiece. The height of the Workstops can be adjusted to allow for clearance of your tool. Each End or Side Workstop includes two 1/4” screws and two washers to attach to the pallet. Modular Vacuum Chuck Workstops 1" Side Workstop, Catalog No.: 10255 1" End Workstop, Catalog No.: 10256 Modular Vacuum Chucks 1" Side Workstop Catalog No.: 10255 Quantity: $35.00 each Modular Vacuum Chucks 1" End Workstop Catalog No.: 10256 Quantity: $35.00 each
Vise-Block	Attach to the bottom of the Modular Vacuum Chuck to allow for use in a 5" or larger milling vise. Steel Black oxide construction. Six 1/4" - 20 screws included. 5" width x 7" length x .5" height Vise-Block Catalog No.: 10260 Quantity: $135.00 each
Vise Stop-Pin	Steel Pin locates the Modular Vacuum Chuck in the milling vise. Screw into any of the twelve Stop-Pin holes to consistently locate the pallet in your vise. Vise Stop-Pin Catalog No.: 10252 Quantity: $24.00 each

2L patent pending Hex Workstops and Adjustable Edge Clamps can securely hold a wide range of workpiece sizes. Use with 2L Vacuum Chucks, Pallet-Vise and other pallet workholding and fixturing systems.

Adjustable Hex Workstops and Edgeclamps holding workpiece in a Pallet-Vise with the Pallet Cover.

Low profile for tight workpiece clearance.
For use with all 2L Vacuum Chucks and Pallet Systems, and can easily be used with other workholding pallet systems.
Tightening the standard screw moves the Edge Clamp toward the workpiece to hold workpiece in place.
Hold small, thin, corners, or odd shaped workpieces.
Excellent for prototyping - reduces the need for custom fixtures to hold workpiece.
Steel, or hardened steel - black oxide construction.
See Set Up Examples.

Adjustable Hex Workstops and Edge Clamps
Adjustable Hex Workstop	Varying distances from each edge to the central hole (0.050” each step) allows adjusting workpiece location. Numbered locations allow for repeatable setup. Steel - black oxide construction. Low profile - 3/16” (0.1875”) height. 1/4”-20 screw included. Adjustable Hex Workstop Catalog No. 10247 Quantity: $19.00 each
Adjustable Edge Clamp	Provides 1.25” clamping travel range when used with an Adjustable Hex Workstop. Tightening the included Flat Head Screw moves the clamp towards the workpiece. Numbered locations for repeatable setup. Hardened steel - black oxide construction. Low profile - 3/16” (0.1875”) height. 1/4”-20 screw included. Adjustable Edge Clamp Catalog No. 10248 Quantity: $22.00 each
Adjustable Corner Edge Clamp	Cutout on ends allows holding corners of workpieces or circular workpieces. Provides 1.25” clamping travel range when used with an Adjustable Hex Workstop. Tightening the included Flat Head Screw moves the clamp towards the workpiece. Numbered locations for repeatable setup. Hardened steel - black oxide construction. Low profile - 3/16” (0.1875”) height. 1/4”-20 screw included. Adjustable Corner Edge Clamp Catalog No. 10272 Quantity: $28.00 each
Adjustable Thin Corner Edge Clamp	Thin (0.06”) cutout ends allows holding very thin workpieces, corners of workpieces, or circular workpieces. Provides 1.25” clamping travel range when used with an Adjustable Hex Workstop. Tightening the included flat head screw moves the clamp towards the workpiece. Numbered locations for repeatable setup. Hardened steel - black oxide construction. Low profile - 3/16” (0.1875”) height overall (0.06” on ends). 1/4”-20 screw included. Adjustable Thin Corner Edge Clamp Catalog No. 10273 Quantity: $32.00 each

Engraving Tools, Endmills & Cutters
Spring Loaded Engraving Tools
Vacuum Chucks for Workholding

2L inc.

Modular Vacuum Chuck (8" x 12") Accessories

8" x 12" Modular Vacuum Chuck Accessories & Vacuum Workholding Accessories

Accessories for 8" x 12" Modular Vacuum Chucks

$6.00 Pkg. of two

$198.00 each

$21.00 roll

$49.96 roll

$16.25 each

$32.00 each

$21.50 each

$26.50 each

$24.00 each

$16.60 each

$69.95 each

$67.32 each

$13.00 pkg. of 8

$4.00 pkg. of 10

$35.00 each

$35.00 each

$135.00 each

$24.00 each

Adjustable Hex Workstops and Edge Clamps

$19.00 each

$22.00 each

$28.00 each

$32.00 each

Engraving Tools, Endmills & CuttersSpring Loaded Engraving ToolsVacuum Chucks for Workholding

2L inc.

Modular Vacuum Chuck (8" x 12") Accessories

8" x 12" Modular Vacuum Chuck Accessories & Vacuum Workholding Accessories

Accessories for 8" x 12" Modular Vacuum Chucks

$6.00 Pkg. of two

$198.00 each

$21.00 roll

$49.96 roll

$16.25 each

$32.00 each

$21.50 each

$26.50 each

$24.00 each

$16.60 each

$69.95 each

$67.32 each

$13.00 pkg. of 8

$4.00 pkg. of 10

$35.00 each

$35.00 each

$135.00 each

$24.00 each

Adjustable Hex Workstops and Edge Clamps

$19.00 each

$22.00 each

$28.00 each

$32.00 each

Engraving Tools, Endmills & Cutters
Spring Loaded Engraving Tools
Vacuum Chucks for Workholding