2L Home

Engraving Tools, End Mills & Cutters
Spring Loaded Engraving Tools
Vacuum Chucks for Workholding

2L inc.

4 Kane Industrial Drive
Hudson, MA 01749
Tel: (978)567-8867
Contact Us
About Us Catalog Contact Us Testimonials Videos Cart

On Sale!

On Sale Through August 31, 2015 - Only While Supplies Last!


3/8" EXTENDED TOOL HOLDER
---
3/4" INDUSTRIAL NO-CLOG AIR EXHAUST SILENCER
---
2 PALLET, 8" X 12" MODULAR VACUUM CHUCK SYSTEM W/AIR VENTURI VACUUM
---
PRO 1 & PRO 2 ENGRAVING SOFTWARE PROGRAMS


3/8" (.375") Diameter Extended Tool Holder
Holds .125" (1/8") Diameter Tool Bits


Extended Tool Holder - Straight Shank Tool Extension

  • Use this Extended Tool Holder for operations where an extra long tool is needed to reach into deep cavities or pockets and where larger diameter collet holding devices will not allow getting close enough to the cavity or pocket walls.
  • 3/8" (0.375") overall shank diameter.  
  • The straight shank (0.375" diameter) allows you to control how far the tool holder protrudes from your collet.
  • 6.0" overall length.
  • Holds 1/8" (0.125") diameter Tool Bits.
  • Change the cutting tools from the front without removing the tool holder from the spindle.
  • This tool is designed for light finishing cuts only.
Operating Notes: Protrude the Extended Tool Holder from your collet the minimum amount necessary to reach into the pocket or cavity. The shaft may bend or whip if protruded too far from the collet or too much sideways cutting pressure is applied. Due to the extremely small shank diameter and length of the tool, the run out of the tool can be as much as 0.004" when the tool is protruded the full length of the shaft. The Extended Tool Holder is produced from high strength tool steel so it can be trammed in straight (straightened) in your spindle if necessary.


3/8" Diameter Extended Tool Holder

ORDER

Extended Tool Holder - Straight Shank Extension

- 0.375" (.3/8") Shank Diameter
- Holds 1/8" Diameter Tool Bits.
- 6.0" Overall Length

 

 

 

Offer expires 08/31/2015

Extended Tool Holder for 1/8" Cutters:

Part No.: 10782
Quantity:

Price: $99.00 each

Sale Price: $80.50 each

Heavy Duty Industrial Air Exhaust Silencers/Mufflers
Reduce Air Exhaust Noise from 20 - 30db

 

Straight-through wide open path resists clogging.
Solid Flat Black Anodized Aluminum for harsh environments.
 

  • Thick walled rugged design allows for use in the harshest environments, including the oil and gas industry marine applications.
  • Wide open straight through path resists clogging and produces no back pressure.
  • Opening of 1/2” (12.7mm) or 3/8” (9.5mm) allows large particles (dirt, rust, contaminants) to pass straight through.
  • Effectively reduces noise from both continuous flows and intermittent popping type noises.
  • Removable foam insert increases the noise reduction. The foam insert may be removed for high temperature applications.
  • Two piece design allows opening the muffler for inspection or replacing the foam insert.  No tools are needed to open the muffler.
  • Typical Applications:
    • Oil and Gas Industry gas blow off exhaust valves - marine environments.
    • Air compressor intakes and exhausts.
    • Furnace exhausts.
    • Air knife and air dryer blow-off applications.
    • Air tools and pneumatic air cylinder exhausts.
    • Blow mold exhausts Air guns.

Heavy Duty Industrial No Clog Silencer

NPT / Male Pipe Thread Length O.D. I.D. (thru-hold diameter, min.) Approximate Noise Reduction Levels With Foam Insert Approximate Noise Reduction Levels With Out Foam Insert Part No.
3/4" 5.5" (140mm) 1.75" (44mm) 1/2" (12.7mm) 30db 20db 10787

3/4" Heavy Duty Industrial No-Clog Air Exhaust Silencer

ORDER


3/4" M NPT

Heavy Duty/Industrial No-Clog Air Tool Exhaust Silencer

 

 

 

2L manufactures many sizes No Clog Air Exhaust Silencers.  See all No Clog Air Silencers.

Offer expires 08/31/2015

3/4" M NPT
Heavy Duty No-Clog Air Exhaust Silencer

Part No.: 10787

Quantity:
Price: $48.00 each
Sale Price: $42.00 each




 

Complete Vacuum System
2 Pallet, 8" x 12" Modular Vacuum Chuck with Air Venturi Vacuum

 

Complete Vacuum Chuck & Pump System

ORDER


2 Pallet:  8" x 12" Modular Vacuum Chuck w/ Air Venturi Vacuum Pump - Complete System

This Complete System Includes:

  • 2 - Modular Vacuum Chucks 8" x 12" x 1.45" (Part No.: 10275)
  • 1 - Air Venturi Vacuum Generator Pump (Part No.: 10033)
  • 1 - No Clog Air Exhaust Silencer (Part No.: 10031)
  • 1 - Vacuum Manifold (Part No.:10270)
  • 2 - Adjustable Edge Clamps 0.1875” Height (Part No.: 10248)
  • 2 - Adjustable Hex Workstops 0.1875” Height (Part No.: 10247)
  • 60 - Vacuum Sealing Plug Screws & O-Rings (Part No.: 10246, 6 pkgs./10 ea.)
  • 10 feet - 1/8" Gasket Cord
  • 1 - Gasket Sheet: 8”x12”x0.125” (Part No.: 10253)
  • 1 - Vise Stop-Pin (Part No.: 10252)
  • 16 - Vacuum Plugs (Part No.: 10254, 2 pkgs./8 ea.)
  • 1 - Vacuum Connector (Part No.: 10271)
  • 2 - Alignment Pins (Part No.: 10356, 1 pkg./2 ea.)
  • 6 - Multiple Pallet Connectors (Part No.: 10258)

Replaceable Top Plates are available with varied configurations to protect the surface of your Vacuum Chuck.

Offer expires 08/31/2015

Two Pallet 8" x 12" Vacuum Chuck w/ Air Venturi
Complete System

Part No.: 10536
Quantity:

Price: $1,719.25 each

Sale Price: $1,570.25 each



PRO 1 and PRO 2 Engraving Software Programs for CNC Machine Engraving

PRO 1 Engraving Software
See all PRO 1 Features

Pro 2, 4th axis engraving software
See all PRO 2 Features


See 3D Surfacing Engraving Features



PRO 1 & PRO 2 Engraving Software Programs
For CNC Machine Engraving

ORDER

PRO 1 Version - 2L Engraving Software Program

for 3 Axis CNC Machine Engraving
(downloadable program)
 
  • For use with 3 Axis CNC Machines.
  • Place single or multiple imported images, text, incrementing serial numbers, drawn objects such as straight lines, freehand lines, circles, and rectangles all in one layout and create one G-code .nc program.
  • Engrave at a constant depth onto a 3D Surface.
  • Use multiple font styles and sizes for text/numbers.
  • Perform pocketing and reverse pocketing (reverse engraving), spiral or back and forth tool paths.
  • Create incremental serial numbers.
  • Import, Edit, Engrave JPG, BMP, GIF and DXF Files (company logos, drawings, etc).
  • Import and engrave any type of photograph and convert them into lines (vectors) which can be engraved.
  • Draw items (shapes, circles, rectangles, freehand and straight lines).
  • Control text orientation, alignment, spacing, and size of multiple instances of text.
  • Cycle Time Monitor calculates engraving cycle times.
  • The 2L PRO 1 Engraving Software Program operates on Microsoft Windows® 7, 8, XP, and Vista.
  • See complete list of PRO 1 Engraving Software Program Features

The 2L PRO Engraving Software programs are provided as a download program that is installed on your PC.  Installation of the software program requires your PC to have Internet access and either email or print capabilities.

Sale Price Offer Expires 08/31/2015

PRO 1 Engraving Software Program

Part No.: 10676
Quantity:

Price: $599.00 per seat

SALE Price: $499.00 per seat

PRO 2 Version - 2L Engraving Software Program

for 3 & 4 Axis CNC Machines, C-Axis, Multi Axis Lathes
(downloadable program)

  • For use with 3 Axis, 4 Axis, C-Axis, or Multi-Axis Lathes.
  • Wrap engraving around a cylinder.
  • Creates G-code on the face of a part on a rotary axis lathe with polar interpolation.
  • A full featured, complete drawing program which produces standard G-code nc files.
  • Place single or multiple imported images, text, incrementing serial numbers, drawn objects such as straight lines, freehand lines, circles, and rectangles all in one layout and create one G-code .nc program.
  • Engrave at a constant depth onto a 3D Surface.
  • Perform pocketing and reverse pocketing (reverse engraving), spiral or back and forth tool paths.
  • Include multiple font styles and sizes, imported dxf files (company logos, drawings), drawn items (shapes: circles, rectangles, freehand and straight lines, etc.), and incremental serial numbers in one output cnc G-code program (.nc file).
  • Control text orientation, alignment, spacing, and size of multiple instances of text.
  • The 2L PRO 2 Engraving Software Program operates on Microsoft Windows® 7, 8, XP, and Vista.
  • See complete list of PRO 2 Engraving Software Program Features

The 2L PRO Engraving Software programs are provided as a download program that is installed on your PC.  Installation of the software program requires your PC to have Internet access and either email or print capabilities.

Sale Price Offer Expires 08/31/2015

PRO 2 Engraving Software Program

Part No.: 10677
Quantity:

Price: $879.00 per seat

SALE Price: $799.00 per seat

 

These offers cannot be combined with any other discount/offer.
Special pricing available only while supplies last.
All Sales are final.  Offer expires 08/31/2015

 

Shopping Cart
Home Products Tech Help Policies Site Map

Copyright © 2015, 2L inc.