2L Home

Engraving Tools, Endmills & Cutters
Spring Loaded Engraving Tools
Vacuum Chucks for Workholding

2L inc.

4 Kane Industrial Drive | Hudson, MA 01749
Phone: (978)567-8867 | Fax: (978)562-8972
Contact Us
About Us | Catalog | Press Releases | Testimonials

Pallet-Vise Workholding Accessories

Accessories for the Pallet-Vise, Workholding and Fixturing.

All accessories for use with the Modular Pallet-Vise Workholding System appear below.

Page down for details. These are in stock & ready to ship.
You can order below or contact us.


Pallet-Vise shown with Workholding Accessories, Vise-Block, Adjustable Edge Clamps, and Side and End Workstops

Accessories for the Pallet-Vise
Pallet-Vise Side and End Workstops

Pallet-Vise Side and End Workstops		 Attach to the sides and ends of the Vac-Vise or Pallet-Vise to locate the workpiece. The height of the Workstops can be adjusted to allow for clearance of your tool. Each End or Side Workstop includes two 1/4” screws and two washers to attach to the pallet.

Pallet-Vise Workstops
3/4” Side Workstop, Catalog No.: 10265
3/4” End Workstop, Catalog No.: 10266
Catalog No.: 10265

Qty:

$35.00 each

Catalog No.: 10266

Qty:

$35.00 each
Pallet-Cover

Pallet Cover		 Rigid plastic sheet allows drilling through of workpieces while protecting Pallet from damage when using edge clamps (not for vacuum use).  Pre-punched holes match the hole locations of the Pallet.

8” width x 12” length x 1/4” height.
Catalog No.: 10251

Qty:

$30.00 each
Pallet-Vise Multiple Pallet Connector

Pallet-Vise Connector		 Lock two or more Pallet-Vises together to increase the size of the workspace area. May also be used as a clamping area to hold the pallet down to the machine table. Includes four 5/16”-18 screws to connect to your pallet.

A minimum of 2 Pallet-Vise Connectors are needed to connect 2 Pallet-Vise Pallets. When connecting 3 or more Pallet-Vise Pallets, the quantity needed will depend on your Pallet layout configuration.
Catalog No.: 10268

Qty:

$32.00 each
Double Sided
Workholding Tape

Double Sided Workholding Tape 		Firmly holds workpieces in position. One side has a strong permanent adhesive. The other is coated with a removable adhesive. The removable adhesive allows removal of the workpiece without damaging it or leaving residue. It also allows for removal and repositioning of the workpiece many times.

1 roll - 1” width x 36 yards length.
Catalog No.: 10276

Qty:

$18.00 each
Alignment Pin
Alignment Pin for Vac-Vise and Pallet-Vise 		Heavy duty steel pin aligns and guides two or more Pallet-Vise or Vac-Vise Plates together for even surface transition.

2 Alignment Pins are needed to connect 2 Pallets together.

Catalog No.: 10356

Qty:


$6.00 pkg. of 2
Vise-Block
Vise-Block		 Vise-Block shown with Vac-Vise in Machine ViseAttach to the Vac-Vise or Pallet-Vise to allow for use in a 5" or larger milling vise.  Steel Black oxide construction. Six 1/4" - 20 screws included.


5" width x 7" length x .5" height
Catalog No.: 10260

Qty:

$135.00 each
Vise Stop-Pin
Vise Stop-Pin 		Steel Pin locates the Vac-Vise and Pallet-Vise in the milling vise. Screw into any of the twelve Stop-Pin holes to consistently locate the pallet in your vise.
Catalog No.: 10252
Qty:

$24.00 each



2L patent pending Hex Workstops and Adjustable Edge Clamps can securely hold a wide range of workpiece sizes.  Use with 2L Vacuum Chucks, Pallet-Vise and other pallet workholding and fixturing systems.

Adjustable Hex Workstops and Edgeclamps holding workpiece in a Pallet-Vise with the Pallet Cover.      Low profile adjustable workstops and edgeclamps
  • Low profile for tight workpiece clearance.
  • For use on the Modular Vac-Vise Vacuum Chucks, Large Vacuum Chucks, Pallet-Vise, and other workholding pallet systems.
  • Tightening the standard screw moves the Edge Clamp toward the workpiece to hold workpiece in place.
  • Hold small, thin, corners, or odd shaped workpieces.
  • Excellent for prototyping - reduces the need for custom fixtures to hold workpiece.
  • Steel, or hardened steel - black oxide construction.
  • See Set Up Examples.
Adjustable Hex Workstops and Edge Clamps

Adjustable Hex Workstop

Adjustable Hex Workstop

  • Varying distances from each edge to the central hole (0.050” each step) allows adjusting workpiece location.
  • Numbered locations allow for repeatable setup.
  • Steel - black oxide construction.
  • Low profile - 3/16” (0.1875”) height.
  • 1/4”-20 screw included.

Catalog No.: 10247

Qty:

$19.00 each

Adjustable Edge Clamp

Adjustable Edge Clamp
  • Provides 1.25” clamping travel range when used with an Adjustable Hex Workstop.
  • Tightening the included Flat Head Screw moves the clamp towards the workpiece.
  • Numbered locations for repeatable setup.
  • Hardened steel - black oxide construction.
  • Low profile - 3/16” (0.1875”) height.
  • 1/4”-20 screw included.

Catalog No.: 10248

Qty:

$22.00 each

Adjustable Corner Edge Clamp

Adjustable Corner Edge Clamp
  • Cutout on ends allows holding corners of workpieces or circular workpieces.
  • Provides 1.25” clamping travel range when used with an Adjustable Hex Workstop.
  • Tightening the included Flat Head Screw moves the clamp towards the workpiece.
  • Numbered locations for repeatable setup.
  • Hardened steel - black oxide construction.
  • Low profile - 3/16” (0.1875”) height.
  • 1/4”-20 screw included.

Catalog No.: 10272

Qty:

$28.00 each

Adjustable Thin Corner Edge Clamp

Adjustable Thin Corner Edge Clamp
  • Thin (0.06”) cutout ends allows holding very thin workpieces, corners of workpieces, or circular workpieces.
  • Provides 1.25” clamping travel range when used with an Adjustable Hex Workstop.
  • Tightening the included flat head screw moves the clamp towards the workpiece.
  • Numbered locations for repeatable setup.
  • Hardened steel - black oxide construction.
  • Low profile - 3/16” (0.1875”) height overall (0.06” on ends).
  • 1/4”-20 screw included.

Catalog No.: 10273

Qty:

$32.00 each
Home | Products | Tech Help | Policies | Site Map | Copyright © 2010 2L inc.