2L Home

Engraving Tools, Endmills & Cutters
Spring Loaded Engraving Tools
Vacuum Chucks for Workholding

2L inc.

4 Kane Industrial Drive | Hudson, MA 01749
Phone: (978)567-8867 | Fax: (978)562-8972
Contact Us
About Us | Catalog | Press Releases | Testimonials

Adjustable Edge Clamps and Hex Workstops

For Prototype and Production Workholding and Fixturing


2L patent pending Hex Workstops and Adjustable Edge Clamps can securely hold a wide range of workpiece sizes.  Use with 2L Vacuum Chucks, Pallet-Vise and other pallet workholding and fixturing systems.


Adjustable Hex Workstops and Edgeclamps holding workpiece in a Pallet-Vise with the Pallet Cover.      Low profile adjustable workstops and edgeclamps


  • Low profile for tight workpiece clearance.
  • For use on the Modular Vac-Vise Vacuum Chucks, Large Vacuum Chucks, Pallet-Vise, and other workholding pallet systems.
  • Tightening the standard screw moves the Edge Clamp toward the workpiece to hold workpiece in place.
  • Hold small, thin, corners, or odd shaped workpieces.
  • Excellent for prototyping - reduces the need for custom fixtures to hold workpiece.
  • Steel, or hardened steel - black oxide construction.
  • See Set Up Examples.
These are in stock & ready to ship.
You can order below or contact us.


* Adjustable Workstops and Adjustable Edge Clamps have a U.S. utility patent pending.
 
Adjustable Hex Workstops and Edge Clamps

Adjustable Hex Workstop

Adjustable Hex Workstop
  • Varying distances from each edge to the central hole (0.050” each step) allows adjusting workpiece location.
  • Numbered locations allow for repeatable setup.
  • Steel - black oxide construction.
  • Low profile - 3/16” (0.1875”) height.
  • 1/4”-20 screw included.

Catalog No. 10247

Qty:

$19.00 each

Adjustable Edge Clamp

Adjustable Edge Clamp
  • Provides 1.25” clamping travel range when used with an Adjustable Hex Workstop.
  • Tightening the included Flat Head Screw moves the clamp towards the workpiece.
  • Numbered locations for repeatable setup.
  • Hardened steel - black oxide construction.
  • Low profile - 3/16” (0.1875”) height.
  • 1/4”-20 screw included.

Catalog No. 10248

Qty:

$22.00 each

Adjustable Corner Edge Clamp

Adjustable Corner Edge Clamp
  • Cutout on ends allows holding corners of workpieces or circular workpieces.
  • Provides 1.25” clamping travel range when used with an Adjustable Hex Workstop.
  • Tightening the included Flat Head Screw moves the clamp towards the workpiece.
  • Numbered locations for repeatable setup.
  • Hardened steel - black oxide construction.
  • Low profile - 3/16” (0.1875”) height.
  • 1/4”-20 screw included.

Catalog No. 10272

Qty:

$28.00 each

Adjustable Thin Corner Edge Clamp

Adjustable Thin Corner Edge Clamp
  • Thin (0.06”) cutout ends allows holding very thin workpieces, corners of workpieces, or circular workpieces.
  • Provides 1.25” clamping travel range when used with an Adjustable Hex Workstop.
  • Tightening the included flat head screw moves the clamp towards the workpiece.
  • Numbered locations for repeatable setup.
  • Hardened steel - black oxide construction.
  • Low profile - 3/16” (0.1875”) height overall (0.06” on ends).
  • 1/4”-20 screw included.

Catalog No. 10273

Qty:

$32.00 each

Home | Products | Tech Help | Policies | Site Map | Copyright © 2010 2L inc.